增加原廠藍牙模組到原廠音響，
Step By Step
還有Parts Number 歐！！
可以來問問價格
[iframe]http://www.ffoc.co.uk/modules.php?name=Forums&file=viewtopic&t=182822[/iframe]
all parts needed are listed up the top mate
short console with mic 1317579==>16.51歐元
1467152 for focus specific loom ==>66.47歐元 or Fiesta one 1429802
Stalk with voice button 1318965 快撥鍵 ==>42.55歐元
Module 1476159 藍牙模組 ==>164.50歐元
Mic 1363463 麥克風 ==>36.70歐元
Bracket 1353218 藍牙模組固定架 ==>4.97藍牙模組
1231390 * 2 off 螺絲 ==>0.6歐元
1231391 * 1 off 螺絲 ==>0.4歐元
Actualy very easy to do, Will take an hour to anhour and a half. tools needed are a very sharp knife, sterio removaltools, torx drivers/keys, for fiesta loom wire cutters and ellectrictape/ellectrical connectors or heat wrap.
the parts you will need from ford or a breaker focus
short console with mic 1317579 is the part number for cars with out a sunroof @ ￡16.51
1467152 for focus specific loom @ ￡66.47 or Fiesta one 1429802 @ ￡30.69will do the job just need the mic wire extending by about 6 inches andits about half the price its what i used
,
Stalk 1318965@ ￡42.55 ,
Module 1476159 ￡164.50,
Mic 1363463 ￡36.70,
Bracket 1353218 ￡4.97,
1231390 ￡0.60p each hold bracket to car you will need 2 off
1231391 @ ￡0.40p each hold the unit to the bracket you need 1 off
1. Remove the sterio and remove the glove box
the green markings are torx screws that need removing and the red arecovers that have torx screws underneath. Just pull the covers free butnot to hard as they break easily away from the dash
2. Feed the sterio loom out the top half of the sterio area intothe glove box area and connect it to the relevant end of the bluetoothloom. Now feed the new sterio end into the sterio area via the bottomarea
3. You can now connect the new sterio plug into the sterio and refit the sterio making sure no wire looms snag
4. Screw the bluetooth unit to the bracket and plug it in to the loom.Once connected bolt the unit in to the car. This for me was prettydifficult as i have big arms
but do able if you feel up behind the dash you will feel the two mounting points the bracket screws in too
5. Now pull off the cover for the a pillar. It may feel very tight butthe pins that hold it in place work like a ratchet so carefully pullwith both hands till it comes off
6A. Remove the interior light and light surround
6B. (only for people using the fiesta loom) You will now need tocut the plug of either the bluetooth loom or the mic and extend thewire by approx 6" and reattach
7. Run the mic end of the bluetooth loom up from the glove box andup the a pillar, under the roof lining and out through the hole for theinterior light
8. Refit the a pillar cover, this simply pushes back on. Refit the glove box and torx screws making sure no wires snag
9. Now you need to cut the hole in the roof linning for the larger interior light surround with mic vent
10. now clip the mic into the space in the new light surround. Fit the new light surround and refit the interior light
11. Now you will need to swap the old sterio stalk control for the newone with the voice button. Just feel the rear of the stalk you willfeel a recess with a little tab pull this tab and the sterio stalk willcome free. Unclip the plug, plug it into the new stalk and push the newstalk into place
12. Now turn the sterio and search for new device once found start playing around with your new toy
